如何更换199619金牛座的前照灯灯泡?

找到以下1个回答

1个回答
优质解答
晏萱超

# Make sure headlamp is off and open hood.

# Facing the driver's side headlamp, and looking at the headlamp itself, at clock positions 8, 11 and 1 are the headlight housing screws. They all look the same. Using a 10mm socket wrench, remove these 3 screws and set them aside.

# Just to the right of the "11 o'clock" housing screw is a clinch bolt (same hexagonal 10mm sized top as the housing screws). This just needs a few turns to loosen it. As soon as you loosen that up the whole assembly comes right out.

# Gently pull the whole headlight forward. Now you can get at the bulb.

# Disconnect the electrical connector from the bulb. Now the headlamp is free to work with.

# Remove the bulb from the lamp assembly by pulling straight back.

Do not twist, as there are alignment slots built into the lamp assembly socket. It may take some effort to remove the lamp because it has a rubber o-ring type seal - try a bit of wiggling side-to-side while pulling

# Insert new bulb into headlight assembly - don't touch the glass - use gloves, paper towel, or similar

Make sure that the flat surface of the bulb socket is facing upward, and is firmly seated

# Re-attach retainer ring by rotating clockwise

# Reconnect the electrical harness

# Place headlamp back into position. Line up screw holes. Tighten the clinch bolt. Replace housing screws and tighten.

Passenger side headlamp is mirror image of driver's side. Screws at 11, 1 and 4 o'clock positions. Bolt should be to the left of the "1 o'clock" housing screw.

* Do not touch the glass of the new halogen bulb - the oils in the skin will shorten the life-span of the new bulb, or possibly cause the bulb to explode when first turned on

If the bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used

Bulb Numbers:

* FRONT Turn-signal - 3457 AK (amber) * Headlamp - 9007 QL (9007LL optional) * Tail lamp/brake/turn lamp 3157 * Tail lamp/brake lamp (wagon) 3157 * Rear turn lamp (wagon) 3456K * Backup lamp 921 * Backup lamp (wagon) 3156 * License plate lamp (2) 168 * High-mount brake lamp (2) 912 * Rear side marker lamp (wagon) (2) 168 The above information extracted from the Owners Manuals (see below) == == == ==1. Make sure headlamp is off and open hood. 2. Taurus model years 1990-1999: you must remove the whole headlamp to replace the bulb. Not a horrible task. Just annoying. 3. Facing the driver's side headlamp, and looking at the headlamp itself, at clock positions 8, 11 and 1 are the headlight housing screws. They all look the same. Using a 10mm socket wrench, remove these 3 screws and set them aside. 4. Just to the right of the "11 o'clock" housing screw is a bolt (same hexagonal 10mm sized top as the housing screws). This just needs a few turns to loosen it. 5. Gently pull the whole headlight forward. Now you can get at the bulb. 6. Disconnect the electrical connector from the bulb. Now the headlamp is free to work with. Remove the bulb, replace with a new bulb, make sure the bulb housing cylinder is in place and reconnect the electical. 7. Place headlamp back into position. Line up screw holes. Tighten the bolt. Replace housing screws and tighten. 8. Passenger side headlamp is mirror image of driver's side. Screws at 11, 1 and 4 o'clock positions. Bolt should be to the left of the "1 o'clock" housing screw.

这篇文章对你有帮助吗?

不是
展开阅读全文
更多回答(0)

不满意!建议你搜索下面这些,看看结果

如何更换199619金牛座的前照灯灯泡? 次/年
如何更换1996-1999金牛座的前照灯灯泡? 0
如何更换2000-2005金牛座的前照灯和转向灯灯泡? 0
如何更换1987款本田思域掀背车上的前照灯灯泡? 0
如何更换1996年克莱斯勒城乡面包车的前照灯灯泡? 0
如何更换2000现代口音的前照灯灯泡? 0
如何更换奥迪a6 2008车型的前照灯灯泡? 0
如何更换rover 75上的左前照灯灯泡? 0
如何更换福特金牛座的尾灯或刹车灯灯泡? 0
如何更换1997年三菱幻影的前照灯? 0
如何更换2000辆大众帕萨特的前照灯和日间行车灯? 0
更多全网搜索

搜索历史 全部清除

近期热词

与Linbizi聊天 聊天中

发送